{"id":36,"date":"2019-03-19T08:49:00","date_gmt":"2019-03-18T23:49:00","guid":{"rendered":"http:\/\/quarterrampskate.psilk.com\/en\/?page_id=36"},"modified":"2019-03-19T08:49:00","modified_gmt":"2019-03-18T23:49:00","slug":"ramp-r-make","status":"publish","type":"page","link":"http:\/\/quarterrampskate.psilk.com\/en\/ramp-r-make","title":{"rendered":"cut of materials"},"content":{"rendered":"

If materials are prepared, I cut materials.
\n\"I<\/a><\/p>\n

At first it is a cut of the most relevant R which, well, is the most difficult by lamp production<\/p>\n

“The size of R” depends on a quarter or the size (height) such as mini-lamps to make, and there is the preference, too.<\/p>\n

Generally, is 200cm a standard?
\nWhen it is R200 when height is a microskirt lamp with 60 or 80, for oneself, I feel like it not being practiced too much<\/p>\n

About R, I was considerably at a loss this time.<\/p>\n

With R180, 170,160,150, I temporarily draw a line
\nHowever, I do not understand that I do not make it
\nConsiderably at a loss<\/p>\n

(not practiced not being fun when R is too loose
\nOn the other hand, I feel it is quick, and difficult to do even if it is a small lamp and is too strong-minded)<\/p>\n

The lamp which a friend made in the home this time served as a reference.
\nI seemed to make the lamp of the friend with 70cm in height in R160, but can just play
\nIt was considerably fun<\/p>\n

Therefore I drew a line in R160, but decided to do it in R150 because still it was loose to make this time because there was height only as for 60cm<\/p>\n

Pull of R in case of the lamp production.
\nThe pull flight of R, please take the following into account.
\nI think whether it is the same by not only the quarter lamp but also the mini-lamp production<\/p>\n

\"I<\/a><\/p>\n

<\/p>\n

\"I<\/a><\/p>\n

I wanted to image the appearance condition of the coping on deciding size of R<\/p>\n

However, it is the thing that such time is happy with luxury. . .<\/p>\n

\"I<\/a><\/p>\n

It is the appearance of the jigsaw that I purchased only for beginning to cut of R newly this time<\/p>\n

\"I<\/a><\/p>\n

Do it at a stretch, and cut and bring it down; completion!<\/p>\n

\"I<\/a><\/p>\n

\u30fb\u30fb\u30fbHowever, I’m ashamed to say, the jigsaw is difficult<\/p>\n

Does a way of the progress of the machine get too impatient?<\/p>\n

\"I<\/a><\/p>\n

A grinder comes up to deal. A product of Shin Coe of the electric tool series that this is inexpensive.<\/p>\n

A tool of Shinko is good<\/p>\n

This may be because it is the use frequency of an amateur level, but works good.<\/p>\n

\"I<\/a><\/p>\n

And I cut and bring down the coping moiety. Here is particular about millimeters unit, too and<\/p>\n

\"I<\/a><\/p>\n

I already cut one if I cut one.<\/p>\n

\"I<\/a><\/p>\n

I put it in the real setting place.<\/p>\n

At last I can get the image of the rough size, too. It is thought whether it is a good feeling<\/p>\n

\"I<\/a><\/p>\n

I try to put the coping incidentally.<\/p>\n

\"I<\/a><\/p>\n

Mmm. Good feeling<\/p>\n

Though it is short, I connect it with another one of them on hand and am going to use it\u3002<\/p>\n

There were two shortish single pipe pipe at hand. Because it was ridiculous to buy long one expressly, I thought that you connected it and should use it, but I could not connect it neatly than this thought and should have bought the one which it was different obediently and had a long<\/p>\n","protected":false},"excerpt":{"rendered":"

If materials are prepared, I cut materials. At first it is a cut of the most relevant R which, well, is the most difficult by lamp production “The size of R” depends on a quarter or the size (height) such as mini-lamps to make, and there is the preference, too. Generally, is 200cm a standard? When it is R200 when height is a microskirt lamp with 60 or 80, for oneself, I feel like it not being practiced too much About R, I was considerably at a loss this time. With R180, 170,160,150, I temporarily draw a line However, I do not understand that I do not make it Considerably […]<\/p>\n","protected":false},"author":1,"featured_media":41,"parent":0,"menu_order":10,"comment_status":"open","ping_status":"open","template":"","meta":[],"yoast_head":"\n\n\n\n\n\n\n\n\n\n\t\n\t\n\n\n\t\n