{"id":9,"date":"2019-03-19T08:49:00","date_gmt":"2019-03-18T23:49:00","guid":{"rendered":"http:\/\/quarterrampskate.psilk.com\/en\/?page_id=9"},"modified":"2019-03-19T08:49:00","modified_gmt":"2019-03-18T23:49:00","slug":"preparations","status":"publish","type":"page","link":"http:\/\/quarterrampskate.psilk.com\/en\/preparations","title":{"rendered":"preliminary"},"content":{"rendered":"

At first, in a head, I look for a home center what is how necessary while thinking.
\n\"quarter<\/a><\/p>\n

The surface of the lamp is going to make veneer two-ply<\/p>\n

I think about thickness. When it is 4mm, is it slightly weak 8mm<\/p>\n

Is it slightly weak?<\/p>\n

\"quarter<\/a><\/p>\n

It is indeed too thin at 2.4mm. It is cheap and is attractive.<\/p>\n

\"quarter<\/a><\/p>\n

If it is a …9mm veneer two leaves stack, 9mm is good in terms of strength<\/p>\n

However, it is expected that I have a hard time very much when I really stick it on a lamp because R is hard.<\/p>\n

Probably I am broken at the time of pasting up of R<\/p>\n

\"quarter<\/a><\/p>\n

Therefore it is decided in 5.5mm veneer.<\/p>\n

\"quarter<\/a><\/p>\n

Because I am going to put it like the illustration mentioned above, I purchase five pieces!
\n<\/p>\n

\"quarter<\/a><\/p>\n

I bought the rafter of 3cm *4cm.<\/p>\n

\"quarter<\/a><\/p>\n

The one which 2*4 materials were bigger, and was strong was actually enough, but did it in cost here because this was cheaper (sweat). However, the neighborhood thinks and is balance because you must put a lot it as much as it is thin.<\/p>\n

(2*4 materials are more desirable later because the strong power that is going to return from bending works, and the whole is warped when I stick veneer on a postscript \u2192 R side if after all it is possible)<\/p>\n

\uff08Even if “framework” became durable in 2*4 materials, the truth this neighborhood is balance if I leave the interval between the bars by just that much because the strength of boards such as the veneer to put on the amount surface should be necessary (there is a hole in the surface of the quarter lamp by deterioration). I can make a firm thing (that, e.g., I all display 2*4 materials along an R side w), but lack it very if I prepare materials without thinking about cost even if there is money how much.<\/p>\n

Then I am only all out, and, on the other hand, the strength thinks for the time being for “time when I want to move” while keeping it whether (I can move it in 1-2 adults for the time being practically) as light as possible is an important thing. Possibly, in my home, there is thinking called … which I want to make as light as possible because there may be it when I want to lean it from circumstances such as the baggage in the garage at one time….\uff09<\/p>\n

I bought squared lumber of approximately 360cm 12 first of all (with … considerable a bit)<\/p>\n

There is 360cm in width, but, as for the number to go aside, and to be usable, there are just only 12 because the quarter to make is a plan of around 225cm<\/p>\n

Because there is not thickness, as for this, only 3*4cm is thought that there is considerably few it, but did not want to do quarter in itself heavily too much as above, being all out with one is economical. Because I sold in six bunches, I did not need 18 of them<\/p>\n

A thing lacking strength afterward is the thought that I will take care of if I put reinforcement partially<\/p>\n

As a result, it became somehow, but had a hard time later as such<\/p>\n

I’m sorry in the incomprehensible sentence that it is hard to read<\/p>\n

\"I<\/a><\/p>\n

I bought the jigsaw<\/p>\n

Because it is made with the lamp in the days of the kid and sawed it for spirit, but it is indeed hard
\n\"\u65b0\u8208\u88fd\u4f5c\u6240<\/a><\/p>\n

\u65b0\u8208\u88fd\u4f5c\u6240 4954008982720 SHINKO(\u65b0\u8208\u88fd\u4f5c\u6240) \u5909\u901f\u30b8\u30b0\u30bd\u30fc SJS-400\"\"<\/p>\n

This product. It was a considerably inexpensive thing, but did it in this because the reputation in the net was very good.<\/p>\n

In the first place because a use hits on a jigsaw only for beginning to cut of R of the board,
\nI think that such an inexpensive thing would be good<\/p>\n

I think that the performance does not have any problem at all<\/p>\n","protected":false},"excerpt":{"rendered":"

At first, in a head, I look for a home center what is how necessary while thinking. The surface of the lamp is going to make veneer two-ply I think about thickness. When it is 4mm, is it slightly weak 8mm Is it slightly weak? It is indeed too thin at 2.4mm. It is cheap and is attractive. If it is a …9mm veneer two leaves stack, 9mm is good in terms of strength However, it is expected that I have a hard time very much when I really stick it on a lamp because R is hard. Probably I am broken at the time of pasting up of R […]<\/p>\n","protected":false},"author":1,"featured_media":10,"parent":0,"menu_order":5,"comment_status":"open","ping_status":"closed","template":"","meta":[],"yoast_head":"\n\n\n\n\n\n\n\n\n\n\t\n\t\n\n\n\t\n